ASTM D176电绝缘用固体充填化合物与浸润剂的标准试验方法

ASTM D176 Standard Test Methods for Solid Filling and Treating Compounds Used for Electrical Insulation
ASTM D176 电绝缘用固体充填化合物与浸润剂的标准试验方法

The melting point is useful in selecting a filling or treating compound that will not flow at the operating temperature of the device in which it will be used. It is also essential that it shall not be so high as to injure the insulation at the time of pouring. This test method is suitable for specification, classification, and for control of product uniformity.

1. Scope
1.1 These test methods cover physical and electrical tests for solid filling and treating compounds used for electrical insulation which are fusible to a liquid without significant chemical reaction. Compounds that are converted to the solid state by polymerization, condensation, or other chemical reaction are not included in these test methods.
1.2 These test methods are designed primarily for asphaltic or bituminous compounds, waxes, and fusible resins, or mixtures thereof, although some of these methods are applicable to semisolid types such as petrolatums. Special methods more suitable for hydrocarbon waxes are contained in Test Methods D 1168.
1.3 Provide adequate ventilation when these tests involve heating.
1.4 The test methods appear in the following sections:
p>1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see and .
Note 1
There is no similar or equivalent IEC or ISO standard.
 
2. Referenced Documents (purchase separately)
ASTM Standards
ASTM D5 Test Method for Penetration of Bituminous Materials
ASTM D6 Test Method for Loss on Heating of Oil and Asphaltic Compounds
ASTM D70 Test Method for Density of Semi-Solid Bituminous Materials (Pycnometer Method)
ASTM D71 Test Method for Relative Density of Solid Pitch and Asphalt (Displacement Method)
ASTM D88 Test Method for Saybolt Viscosity
ASTM D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester
ASTM D127 Test Method for Drop Melting Point of Petroleum Wax, Including Petrolatum
ASTM D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
ASTM D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
ASTM D257 Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D937 Test Method for Cone Penetration of Petrolatum
ASTM D1168 Test Methods for Hydrocarbon Waxes Used for Electrical Insulation
ASTM D1711 Terminology Relating to Electrical Insulation
ASTM E28 Test Methods for Softening Point of Resins Derived from Naval Stores by Ring-and-Ball Apparatus
ASTM E102 Test Method for Saybolt Furol Viscosity of Bituminous Materials at High Temperatures
Index Terms
AC loss characteristics; asphaltic compounds; bituminous compounds; coefficient of expansion or contraction; dielectric strength; fire point; flash point; fusible resins; loss on heating; melting point; penetration; permittivity (dielectric constant); softening point; solid filling compounds; solid treating compounds; specific gravity; viscosity; volume resistivity-temperature characteristics; waxes;

更多防火阻燃测试认证，请咨询中国防火网
电话：400-666-7290
网址：www.firete.com
邮箱：info@firete.com

...

 来源：防火网  发布时间：12/11/2013  点击次数：1609